Model Number (Final ordering #/Part No to be defined)
Voltage (V)
Current (A)
Power (W)
RFQ
GT-96600-7056-T3-AP*
56
1.25
70
* (Final ordering #/Part No to be defined)
Specifications
Overview
GlobTek’s GT-96600-7056-AP Power over Ethernet (PoE) injector offers a cost effective and reliable solution for remote powering of wireless LAN access points, IoT sensor hubs, VoIP phones, security cameras and other IP terminals using existing network infrastructure. GlobTek GT-96600-7056-AP injector is configured to provide 70W of power over four pairs using a "Non-IEEE 4PPoE" implementation. When a load is connected, GT-96600-7056-AP immediately applies 56V to all four pairs.
Features
Easy, low-cost system implementation without IEEE802.3af/at/bt identification or classification
10/100/1000Base-T (Gigabit) pass-through
Dual independent current limiters ensure safe (balanced) current on each set of wire pairs
Intelligent fault diagnostics via LED indicator
IEEE802.3 compliant input/output lightning surge and output fault protection
Compact 164 x 55 x 35mm size
Applications
High power PoE equipment
IoT sensor hubs
VoIP phones with video
WiFi, Bluetooth, and multi-band access points
Networked security camera with motorized pan, tilt, and zoom
<210mW, DoE Efficiency Level VI (Patent US9838207B2)
Inrush Current:
<30A @ 230VAC (cold start @ 25°C)
Efficiency:
>88% @ 115VAC, DoE Efficiency Level VI (4-point average)
Output
Output Voltage:
56VDC nom. (54VDC min., 57VDC max.)
Ripple:
100mV max. (peak-to-peak)
Turn-on Delay:
1 second typ. @ 115VAC
Hold-up Time:
8ms typ. @ nominal input voltage and full load
Output Current:
1.24A total, 620mA max. per pair-set
Power Injection Method:
"Non-IEEE 4PPoE"
IEEE802.3 Detection/ Classification:
No/No
Pair-Set 1:
+V: Pins 4,5 - V: Pins 7,8
Pair-Set 2:
+V: Pins 3,6 - V: Pins 1,2
Note 1:
Please note polarity reversal of pair-set 2 compared to typical IEEE802.3 implementation. A compliant IEEE802.3 compliant PD equipment will handle opposite polarity via diode bridge.
Minimum Holding Current:
10mA per pair-set, pulsating output (between 0-56V) if condition not met
Ethernet Pass-Through:
10/100/1000Base-T
LED Indicator:
Off: No output voltage, check AC input power Continuous: Power good (> 10mA on pair-set 1) Flashing @ 1.5Hz: Minimum holding current not met (< 10mA on pair-set 1) Flashing @ 10Hz: Fault condition, over-current or over-voltage
Protections
AC Input Protection:
MOV transient suppressor (10mm diameter) Input line fusing
Output Port Protection:
2X SMAJ58CA, one per pair-set, per IEEE802.3
Overload/Short-Circuit Protection:
Dual independent current monitors, one per pair-set, auto-recovery upon removal of overload condition, per IEEE802.3
EN61000-4-2, 4KV contact discharge, 8KV air discharge (applied to input/output terminals & VCP/HCP)
Radiated RF Immunity:
EN61000-4-3, 3V/m 80-1000MHz, 80% 1KHz AM
EFT/Burst Immunity:
EN61000-4-4, 1KV/100kHz.
Line Surge Immunity:
EN61000-4-5, 1KV differential, 2KV common-mode
Conducted RF Immunity:
EN61000-4-6, 3VRMS, 80% 1KHz AM
Voltage Dip Immunity:
EN61000-4-11
Mechanical
Dimensions:
164 x 55 x 35mm
Weight/Mass:
0.59lb, 264g
AC Input Connector:
IEC60320 inlet: C14, C8, C6, or C18 style
Data and Data + Power Connectors:
Fully shielded RJ45
Special Options
Custom labels/markings
Reduced output power rating
Special housing colors
PoE Interoperability
GT-96600-7056's interoperability performance was verified with various third party PoE systems and products. Digital data pass-through performance was also verified. Please see below tables.
Derating Curve
Qty (ea.)/Carton
N/A
Individual Box/Gift Box Size (mm)
Egg Crate
Individual Box/Gift Box Color
Master Carton Size (mm)
TBD
Gross Weight (kg)
Label Width (mm)
Label Height (mm)
Input Configuration
Description
IEC 60320/C14 AC Inlet Connector, Class I, Earth Ground Mates with IEC 60320/C13 Plug
Optional Locking IEC60320 Receptable and cord option available on some models by request.:
Below are standard cordsets which are "not included" (unless stated above); these can be purchased separately or packaged with the power supply. Contact your Sales Engineer if the style required is not shown below. Many more available in different lengths, colors or cable material.
Contact GlobTek for your specific requirements or custom solutions.
Approvals
Below follows a link to the latest regulatory certifications and marks for this specific product. National standards as well as certification schemes are constantly changing and so is the set of certification marks and symbols applicable to this product. Various standards, marks and symbols, and certificates are subject to change at any time without notice.
Additional standards or unique country certifications are available upon request. Please contact Globtek to request a quotation.
Logo
Description
Efficiency: complies to section 301 of Energy Independence and Security Act (EISA) complies with Energy Star tier 2 (North America), ECP tier 2 (China), MEPS tier 2 (Australia), Code of Conduct (Europe)
Patent US9838207B2
Protected by US and international patents, US patent number US9838207B2
Declaration ДС № ЕАЭС N RU Д-US.КА01.В.10453_19 Custom Union of Russia, Belarus and Kazakhstan http://www.globtek.com/redirect/?loc=gost-certificate-eac-declaration
UKCA Certification
Conforms to UL STD. 60950-1 Certified to CSA STD C22.2 NO.60950-1
Conforms to UL STD. 60950-1 Certified to CSA STD C22.2 NO.60950-1
Audio/Video, Information And Communication Technology Equipment - Part 1: Safety Requirements [UL 62368-1:2014 Ed.2] Audio/Video, Information And Communication Technology Equipment - Part 1: Safety Requirements [CSA C22.2#62368-1:2014 Ed.2]
Japan: Voluntary Control Council for Interference (VCCI)