Input Voltage:	Specified: 85-264VAC, Nameplate: 100-240VAC
Input Frequency:	Specified: 47-63Hz, Nameplate: 50-60Hz
No Load Input Power:	<75mW @ 230VAC (EU CoC Tier 2 compliant)
Inrush Current:	30A @ 115VAC, 60A @ 230VAC typ. (at peak of AC line, cold start)
Efficiency:	78.7% min. (CEC&DOE Level VI compliant), 79.0% min. (EU CoC Tier 2 compliant)

Output

Turn-on Delay:	3 seconds max.
Rise-Time:	100ms max.
Output Regulation	± 5% (measured at the end of a 1.2m long 20AWG USB cordset)
Ripple:	100mV (using a 47µF low-ESR cap + 0.1µF ceramic capacitor, measured @ 20MHz BW)
Transient Response:	10% max. deviation (with 25-75% load step), 1ms max. recovery time
Hold-up Time:	5ms min. (100VAC and full load)

Protections

Input Protection:	MOV transient suppressor, input line fusing
Over-Current Protection:	110% to 150%, auto-restart
Over-Voltage Protection:	10VDC max. (Zener clamp)
Short-Circuit Protection:	Auto-restart
Over-Temperature Protection:	Auto-restart, on-chip temperature sensor

Environmental

MTBF:	1,500,000 hours @ 25°C ambient, full load (Telcordia SR-332, Issue 3)
Operating Temperature:	0°C to 40°C (full load)
Operating Humidity:	20% to 85% relative humidity, non-condensing
Storage Conditions:	-20°C to 60°C / 5% to 95% relative humidity, non-condensing
Cooling:	Natural convection

Safety

Certifications:	IEC60601-1 IEC60601-1-11 IEC62368-1
Dielectric Withstand Voltage:	4000VAC or 5656VDC (primary-to-secondary) 5mA, 1 minute
Output Touch Current:	NC: 100µA max. SFC: 500µA max.
Earth Leakage Current	N/A, Class II input (No protective earth pin, therefore earth leakage is not measured)
Means of Protection:	2 x MOPP (primary-to-secondary)

EMC

Certifications:	IEC60601-1-2 EN55032 (CISPR32) EN55035 (CISPR35)
Conducted Emissions:	Class B, FCC Part 15, Class B (with resistive load)
Radiated Emissions:	Class B, FCC Part 15, Class B (with resistive load)
Harmonic Current Voltage Distortion:	EN61000-3-2, Class A
Voltage Fluctuations/Flicker:	EN61000-3-3
Electrostatic Discharge (ESD) Immunity:	EN61000-4-2, 8KV contact discharge, 15KV air discharge, Criterion A
Radiated RF Immunity:	EN61000-4-3, 10V/m (80MHz-2.7GHz), Table 9, 9-28V/m (385MHz-5.78GHz ), Criterion A
EFT/Burst Immunity:	EN61000-4-4, 2KV/100kHz., Criterion A
Line Surge Immunity:	EN61000-4-5, 2KV differential, Criterion A
Conducted RF Immunity:	EN61000-4-6, 3VRMS, 80% 1KHz AM, Criterion A
Power Frequency Magnetic Field Immunity:	EN61000-4-8, N/A
Voltage Dip Immunity:	EN61000-4-11, Criterion A/B

Enclosure

Housing:	High impact plastic, PC+ABS 94V0, non-vented
Markings:	Laser marked or adhesive-backed label

Derating Curve

Qty (ea.)/Carton

300

Individual Box/Gift Box Size (mm)

43(L)*30(W)*75

Individual Box/Gift Box Color

43(L)*30(W)*75

Master Carton Size (mm)

485 x 335 x 305

Gross Weight (kg)

Label Width (mm)

37.0

Label Height (mm)

19.0

Input Configuration

Description

Australian AS 3112 configuration: SAA 2 pins Class II

Used in Australia, New Zealand, Fiji, Papua New Guinea and Tokelau, has two flat pins forming an inverted V-shape. These flat blades measure 6.3 by 1.5 mm with the Active and Neutral pins of 17 mm in length set 30° to the vertical on a nominal pitch of 13.7 mm. A standard power outlet in Australia provides a nominal voltage of 230 volts at a maximum of 10 amps and always includes an earth connection. As in the UK, its outlets are individually switched for extra safety. Argentina uses a similar plug, with pins 1 mm longer.

User-added image

Output Configuration

Common output connector options:
Click to add to your request.


L Type (Coaxial 5.5x2.5mm plug)	C Type (Coaxial 5.5x2.1mm plug)	K Type (Coaxial 3.5x1.3mm plug)	LL Type (5.5x2.5mm Locking 760k type)	CL Type (5.5x2.1mm Locking S761k type)	Magnetic Connector

YL3 Type (KPPX-3P)	YL4 Type (KPPX-4P)	EJ1/2/3/4/5 (EIAJ RC-5320A type connectors)	MSB Type (Micro USB)	Inquire for custom design

Comprehensive list of GlobTek output cordset options

Contact GlobTek for your specific requirements or custom solutions.