Input Voltage:	90 - 264Vac (Nameplate: 100 - 240Vac)
Input Frequency:	47 - 63Hz (Nameplate: 50 - 60Hz)
Input Current:	10A max. @ 100Vac, 7.5A typ. @ 115Vac, 3.5A typ. @ 240Vac (full load)
No Load Input Power:	< 1.5W @ 240Vac (main-output disabled, remote-off low)
Inrush Current:	< 35A @ 115Vac , < 70A @ 240Vac (cold or warm start)
Efficiency:	92 - 95% typ.
Power Factor:	> 0.95 @ 115Vac, > 0.95 @ 240Vac typ. (25 - 100% load)

Main Output

Total Output Power (Main + Standby + Fan Output):	800W (with forced air cooling) 520W (natural convection cooling)
Turn-on Delay:	< 2 seconds @ 115Vac
Output Voltage Regulation:	± 2.5% (set point tolerance + load/line regulation, measured at output connector)
Load Regulation:	± 1.0% (measured at output connector)
Line Regulation:	± 0.5% (measured at output connector)
Ripple:	< 1% pk-pk (measured with a 47µF low-ESR cap + 0.1µF ceramic cap, measured @ 20MHz BW)
Transient Response:	± 5% deviation max. (with 50% load step), recovery to within ±1% within 1ms
Startup Overshoot:	< 5%
Hold-up Time:	20ms typ. (100% load), 20ms min. (90% load), 50ms typ. (50% load)
Power-Good (PG):	Signal typically goes low ~10ms ahead of AC power failure or entering of protection state
Remote-Off (RO):	Pull 'Remote Off' to COM to disable main output; leave floating or connect to +5V_SB otherwise
Remote-Sense (SNS):	Up to 450mV total cable-drop compensation, reverse and short circuit protected. Connect SNS+/SNS- leads to point-of-load with twisted pair wire. (Note 1)
Output Voltage Fine Adjustment:	Via potentiometer, ±5% adjustment range (Note 1)
Note 1 (Current derating when Vout > Vnom):	Cable drop compensation (SNS) and output voltage fine adjustment can raise the output voltage at the power supply PCB above nominal. The current rating shall be reduced by the same percentage as the output voltage is increased. Reducing the output voltage below nominal does not increase the current rating.

Standby Output

Output Voltage:	5V
Output Current:	1A
Output Voltage Regulation:	± 5.0% (set point tolerance + load/line/cross regulation)
Ripple:	2% pk-pk (using a 47µF low-ESR cap + 0.1µF ceramic cap, measured @ 20MHz BW)
Hold-Up Time:	20ms min.
Always On?	Yes

Fan Output

Output Voltage:	12V
Output Current:	0.6A
Output Voltage Regulation:	± 15.0% (set point tolerance + load/line/cross regulation)
Ripple:	1% pk-pk (using a 47µF low-ESR cap + 0.1µF ceramic cap, measured @ 20MHz BW)
Always On?	Automatic on/off control based on power supply PCBA temperature

Protections

Input Protection:	MOV transient suppressor, dual high breaking capacity fuses
Input Under-Voltage Protection:	Off @ 70Vac typ., Restore @ 80Vac typ.
Over-Voltage Protection:	110-150%, latching, cycle AC power to reset
Over-Current Protection:	Enters CC mode when Iout is ~115% of nominal rating; CC operation is maintained for 75 < Vout < 100%; Cycling protection activates when Vout collapses to <75% of nominal value; auto-recovery
Short Circuit Protection:	Non-latching with auto-recovery
Over-Temperature Protection:	Latching, cycle AC power to reset

Environmental

MTBF:	1,500,000 hours @ 25°C ambient, full load (Telcordia SR-332, Issue 3)
Operating Temperature:	-20°C to 50°C (full output power), -20°C to 70°C (with derating)
Storage Temperature:	-40°C to 85°C
Humidity:	0% to 95% relative humidity, non-condensing
Altitude:	5000m max.
Vibration:	Conforms to EN60068-2-6

Safety

Certifications:	IEC60601-1 IEC62368-1 IEC60335-1
Isolation Options:	Functionally earthed "F4" (Output floating w.r.t. earth) Earthed output "E1" (V- tied to earth)
Dielectric Withstand Voltage:	4000Vac or 5656Vdc (primary-to-secondary) 1768Vac or 2500Vdc (primary-to-earth) 1500Vac or 2121Vdc (secondary-to-earth) ["F4" option only, N/A for "E1"]
Output Touch Current:	NC: <80µA, SFC: <120µA (functional earth "F4") NC: <5µA, SFC: <275uA (earthed output "E1") Tested per IEC60601-1 @ 264Vac
Earth Leakage Current:	NC: <250µA, SFC: <500µA (functional earth "F4") NC: <300µA, SFC: <600µA (earthed output "E1") Tested per IEC60601-1 @ 264Vac
Means of Protection:	2 x MOPP (primary-to-secondary) 1 x MOPP (primary-to-earth) 1 x MOPP (secondary-to-earth) ["F4" only, N/A for "E1"]
Earth Continuity:	"E1" only: < 0.1Ω between AC input connector earth pin and output negative (MAIN_RTN)

EMC

Certifications:	IEC60601-1-2 EN55032 (CISPR32) EN55035 (CISPR35)
Conducted Emissions:	Class B, FCC Part 15 (with resistive load)
Radiated Emissions:	Class B, FCC Part 15 (with resistive load)
Harmonic Current Voltage Distortion:	EN61000-3-2, Class A
Voltage Fluctuations/Flicker:	EN61000-3-3
Electrostatic Discharge (ESD) Immunity:	EN61000-4-2, 10KV contact discharge, 20KV air discharge (applied to input, output, or control connectors), Criterion A
Radiated RF Immunity:	EN61000-4-3, 10V/m (80MHz-2.7GHz), Table 9, 9-28V/m (385MHz-5.78GHz ) Criterion A
EFT/Burst Immunity:	EN61000-4-4, 4KV/100kHz, Criterion A
Line Surge Immunity:	EN61000-4-5, 2KV differential-mode, 4KV common-mode, Criterion A
Conducted RF Immunity:	EN61000-4-6, 3VRMS, 80% 1KHz AM, Criterion A
Power Frequency Magnetic Field Immunity:	EN61000-4-8, 30A/m, Criterion A
Voltage Dip Immunity:	EN61000-4-11, Criterion A/B

Mechanical

Dimensions - U-Frame (GTM968000P):	152.4 x 101.6 x 40.6mm (6.00" x 4.00" x 1.60") nom.
Dimensions - w/ Perforated Top Cover (GTM968000P-C):	152.4 x 101.6 x 47.0mm (6.00" x 4.00" x 1.85") nom.
Dimensions - Enclosed with Top Fan (GTM968000P-TF):	138.0 x 101.6 x 67.1mm (6.00" x 4.00" x 2.64") nom.
Dimensions - Enclosed with End Fan (GTM968000P-EF/-EFI):	185.4 x 101.6 x 47.0mm (7.30" x 4.00" x 1.85") nom.
Fan Audible Noise:	30-40dBA typ.
Fan Airflow Direction:	-TF: Blows air into power supply, exhausts out of AC and DC ends -EF/-EFI: Pulls air through power supply, exhausts out of AC end
Note 2 (Mounting to end-application enclosure):	Refer to the mechanical drawing for the max. penetration depths of mounting screws used to secure the power supply to the end-application enclosure. Failure to adhere to the specified depths may create a safety hazard.

Input/Output Connectors

AC Input Connector for U-Frame, -C, and -TF (J1):	Connector on PCB: Molex 2159151003 Recommended mate: Molex 2159131003 Pinout: 1: Neutral \| 2: N/C \| 3: Line
Earth Lug for U-Frame, -C, and -TF (J2):	Kang Yang PCH250 (0.250" x 0.031" Faston) Recommended mate: TE Connectivity/AMP 2-520184-2
AC Input Connector for -EF:	Connector on enclosure: TE/AMP 350767-1 Recommended mate: TE/AMP 350766-1 Pinout: 1: Line \| 2: Neutral \| 3: Earth
AC Input Connector for -EFI:	Connector on enclosure: IEC60320 C14 inlet Recommended mate: IEC60320 C13 power cord
Main Output Connectors for -M5 Suffix (J3A, J3B):	Connector on PCB: 2 x M5 PCB terminal Recommended mate: M5 or #10 ring terminal (brass/copper) Recommended mounting torque: 2.0Nm Pinout: J2A: +VOUT \| J2B: MAIN_RTN
Main Output Connector for -CN Suffix [Available for Iout ≤36A only] (J3):	Connector on PCB: Molex 0874271242 Recommended mate: Molex 39012125 Pinout: 1, 2, 3, 7, 8, 9: +VOUT \| 4, 5, 6, 10, 11, 12: MAIN_RTN
Standby Output + Signal Connector (J4):	Connector on PCB: Amphenol 98414-G06-06LF Recommended mate: Amphenol 10073599-006LF Pinout: A01: Remote Off \| A02: SNS+ \| A03: SNS- \| B01: Power Good \| B02: COM \| B03: +5V_SB
Fan Output Connector (J5):	Connector on PCB: Molex 22-04-1021 Recommended mate: Molex 22-01-1022 Pinout: 1: COM \| 2: +FAN
Note 3 (MAIN_RTN / COM connections):	To prevent main output current from returning through connector J3, MAIN_RTN and COM are internally separated by a 2.2Ω resistor. MAIN_RTN and COM may be connected together at the end-system PCB.

Derating Curve

Qty (ea.)/Carton

Individual Box/Gift Box Size (mm)

Individual Box/Gift Box Color

Master Carton Size (mm)

TBD

Gross Weight (kg)

Label Width (mm)

TBD

Label Height (mm)

TBD

Input Configuration

Description

Mini-Fit Max Vertical Header, Single Row
User-added image